Exterior
-
Sale!
Out of stock
XS FRONT GRILLE & HEADLAMP SURROUND Code: DA1968 Black with silver mesh Defender - non-air-con The new XS Enhancement range from Britpart is the perfect way to give your Defender a fresh new look. The front grille, side grille and bonnet vent designs are exclusive to Britpart. For fixing kit please see DA1169 (qty x 2 required) & DA1138. -
WKT100020 Defender Stainless Steel Fuel filter Guard Mud Shield TD5 90 / 110 / 130, these are prone to going rusty falling off or not being replaced by garage fitters. Essential to keep the filter safe from off Roading or green lane driving. These will also fit Disco 2 and defender TDCI with some light modification.- Stainless steel
- comes with backing plate and front plate.
- powder coated in black
- OEM Number WKT100020
-
-
WIND DEFLECTOR KIT Code: DA6070 Front & rear 4 piece kit Discovery 1 Range Rover Classic No drilling required for fitment. The Britpart wind deflectors will reduce buffeting and wind noise when driving with the window open. Custom designed for each vehicle and easily attached - no drilling required for fitment! -
AFU1075 Wheel arch clip, these are 6mm plastic trim clips a perfect replacement for the land rover clips used to attach the plastic wheel arch surround or spat on the defender (1987 - 2006 ). The centre pin of the plastic clip is pushed through and expands to hold the fastener in place and keep the spat secure The clip is high quality alternative to the Land Rover original part. Land Rover Defender 90/110 (1987 - 2006 ) PACK OF 10 -
-
TWIN SHOCK TURRETS Code: DA6322L 2” Lift Front Defender Discovery 1 Range Rover Classic Sometimes off-road conditions can be serious enough to test the standard equipment on your Land Rover to its maximum One of the critical components that takes most of the abuse is the suspension system. When using the standard single shock absorber configuration it is not unknown for the shock absorber to break the factory fitted turret mount. These shock absorber turrets from Britpart give you confidence that your vehicles suspension will tackle the terrain you take it through with greater ease. The single shock absorber turret is manufactured from heavy-duty steel and replaces the existing turret mount which is susceptible to corrosion by allowing a build up of dirt inside which is hard to clean thoroughly. The new design is harder wearing and easier to clean. The twin shock absorber turret is manufactured from the same quality steel as the single shock absorber turret but allows for the fitment of an additional shock absorber. The benefits of having extra shock absorbers fitted to your Land Rover is that any extreme force encountered is divided between the two shock absorbers for a more comfortable ride for you and your passengers. Using twin shocks is also beneficial when carrying loads both on and off-road as it improves the load carrying ability of the vehicle. An additional benefit is that when changing shock absorbers there is no need to remove the turrets. Note - Fitting shock absorber turrets may require some vehicle modification, please ask distributor for full details. -
TWIN SHOCK BRACKETS - KIT Code: DA6324 Rear Defender Discovery 1 Range Rover Classic Sometimes off-road conditions can be serious enough to test the standard equipment on your Land Rover to its maximum One of the critical components that takes most of the abuse is the suspension system. When using the standard single shock absorber configuration it is not unknown for the shock absorber to break the factory fitted turret mount. These shock absorber brackets from Britpart give you confidence that your vehicles suspension will tackle the terrain you take it through with greater ease. The single shock absorber bracket is manufactured from heavy-duty steel and replaces the existing turret mount which is susceptible to corrosion by allowing a build up of dirt inside which is hard to clean thoroughly. The new design is harder wearing and easier to clean. The twin shock absorber bracket is manufactured from the same quality steel as the single shock absorber bracket but allows for the fitment of an additional shock absorber. The benefits of having extra shock absorbers fitted to your Land Rover is that any extreme force encountered is divided between the two shock absorbers for a more comfortable ride for you and your passengers. Using twin shocks is also beneficial when carrying loads both on and off-road as it improves the load carrying ability of the vehicle. An additional benefit is that when changing shock absorbers there is no need to remove the brackets. Notes > Rear brackets involve some welding to fit. > Fitting shock absorber brackets may require some vehicle modification, please ask distributor for full details. -
Treesliders Rocksliders Sill Footsteps Defender 110 – Pair COD: DUM0003 Hardy and comfortable Treeslider, with just one component you will have three major uses: Footsteps, Treeslider and Sill -
Terrafirma Dakar Alloy Wheels for Defender Satin Black These incredibly strong 12 spoke Rally Raid style alloy wheels each have a load rating of 1450kg, which makes them suitable for on-road and heavy off-road use. Fitment: 90/110/130/D1/RRC 7x16 ET33- Satin black or silver
- load rating 1450kgs
- 7x16 ET33
- set of 4
-
-
SWING AWAY REAR DOOR MOUNT SPARE WHEEL CARRIER Code: DA2232G Defender - all models Series Note - Only suitable for wheels with a positive offset of 20mm or less -
SWING AWAY REAR DOOR MOUNT SPARE WHEEL CARRIER Code: DA2274 With half door tailgate Defender -
SWING AWAY REAR DOOR MOUNT SPARE WHEEL CARRIER Code: DA2232 Defender - all models Series -
-
-
Full set of wheel nuts- Discovery 2
Protect your valuable wheels and tyres from theft!
Kit contains - > 5 x locking nuts > 5 x spare caps > 18 x normal nuts (inc caps) > 1 x key > 1 x remover tool -
SPRING SEAT Code: NRC9700GALV Galvanised Defender Discovery 1 Range Rover Classic -
RACK MOUNT CLAMPS Code: SACS001 Single Single clamp > Anodized clamp - upper and lower sections > Protective rubbers - protects roll-cage finish > M8 stainless bolts and spring washers For mounting accessories such as a roof-rack, snorkel or aerial to your roll-cage. Suitable for any Safety Devices Expedition external roll-cage, as well as any other roll-cage which uses 45mm diameter tubing. The upper mounting hole is M8 threaded. -
SEEKER-X LED With Integrated Front Position Lamp (Side Light) New to Range stylish looking led light. this is for one led lamp so will need to purchase 2 if you want a pair. SEEKER-X 40W – 245mm With Integrated Front Position Lamp (Side Light) Dimensions (mm): 245 x 103 x 72 Voltage: 12/24V Multivolt Beam Type: Driving Beam Approval: ECE R112, R7, R10 Ingress Protection: IP68 Raw Lumens: 3520lm Current Draw (13.8 / 28V): 0.89A / 0.89A Housing Heavy-Duty Aluminium Connector Deutsch -
SEAL KIT DOOR HANDLE Code: STC617 -
SEAL - ROOF SIDE MOULDING ( REAR UPPER BODY ) Code: DBF500040 -
Defender 16" Sawtooth in Gloss black. This has a big lip to create a dish style Alloy to give you that aggressive look. -
ROOF CROSS RAIL Code: DA4711 Explorer roof rack Gutter mount 4kgs Defender 90 - hard top & station wagon Defender 110 - hard top & station wagon Defender 110 - double cab/crew cab pick-up Defender 130 - double cab/crew cab pick-up Additional roof cross rails for use without a roof rack for use as, for example, a roof bar, basic tent support, attaching a roof storage box or to spread additional load on the Safety Devices' roof rack. Refer to owners handbook for recommended maximum weight. -
Ring Rechargeable UNDER BONNET LAMP- 3 x 5W LEDs provide 1000 lumens light output
- Long operating time allows full working day usage
- 3 levels of light output
- 6000K colour temperature for bright white light
- 40º adjustable head to shine light on the engine bay exactly where it is required
- 60º wide angle illumination
- Sturdy polycarbonate, ABS and Aluminium construction
- Rechargeable 3.7V 10400mAh Li-ion battery
- Hook design allows usage with different vehicle types including, cars, vans and 4x4s
- Illuminated battery status indicator
- Includes AC mains adaptor
- Batteries Included
- Type: RECHARGEABLE
- 1 x CUSTOM
-
Rigid Industries 1x2 65° DC Scene Light prodcues 1100 raw lumens and features a vertical spread of 69° and a horizontal spread of 65°. Using the latest LED technology, all new patent pending optic system, minimal amp draw, and extreme output, the 1x2 65° Scene Light is the perfect area lighting solution. This versatile light can be mounted to your RV, toy hauler, tractor trailer, fire truck and can even be mounted to the undercarriage of your vehicle. Limited Lifetime Warranty. 1x2 65º DC Scene Light - Black Family LED Scene Lighting By Rigid Industries Optics Flood LED Color Clear Finish Color Black Mount Type Surface Shipping Dimensions 5.75 × 4.875 × 2.375 in Product Weight 0.53 lb Sold As Single Features- 65˚ Horizontal Spread X 69˚ Vertical Spread
- Flat Mounting Surface
- Available with Cool White or Amber LEDs
- 9-36 V DC
- IP68 Compliant
- Powder Coated Aluminum Housing
- Watts 9
- Amp Draw 0.75
- LED's 3
- Raw Lumens 1100
- Lux @ 10m 6.95
- Beam Distance 26.4 m
- Peak Beam Intensity 695 cd
-
Sale!
Rigid D-SS SIDE SHOOTER LED CUBE LIGHT .... is One of Rigid’s most versatile, compact lighting solutions just got better with the D-SS, Dually SideShooter LED cube. Perfect for any application that requires a wide spread beam, including A-Pillars, Fog Lights, and motorcycle applications. The D-SS cube incorporates the same powerful optics and legendary LED technology as Rigid’s popular D-Series lights but with the added benefit of additional LEDs aimed to the side for a much broader beam. The D-SS fixtures boast up to 120-degrees of horizontal lighting coverage when used in pairs or when used in the single light applications. The main forward-facing LEDs are available with Rigid’s advanced Flood, Spot, or Driving optics, so there’s a D-SS lighting solution for nearly any application. The D-SS LED lights are available in pairs with three side-shooting LEDs on one side of each fixture, or in single applications with a pair of side-shooting LEDs on both sides of the fixture. Only Rigid provides a broad, powerful lighting solution in such a compact package.- life time guarantee
- comes with loom and relays
- gives better viability for side out put compared to other brands
-
Rear Sill Channel Bracket Galvanized 347436 for Land Rover Defender Rear Sill Channel Bracket Galvanised For Land Rover 90 110 Defender Brand New Top Quality reproduction of Landrover part no. 347436 Laser cut and CNC bent made from 2mm steel and hot dip Galvanized, 100% accurate. Fits all Defenders 90,110,127,130 apart from the 110 5door station wagon. Very high quality OEM NUMBER 347436 -
REAR LAMP GUARD Code: DA4349 Round ABS plastic Reverse, Fog & NAS Single Defender - all models Protect those valuable lights from accidental damage either on or off-road! Add style and some protection to your Land Rover with this new product. This is a tough ABS plastic rear light guard for your Defender.These will not rust and you don't need to drill your car to fit these - fitted in seconds. They fit the fog and reversing light and the NAS (North American Spec) lights. -
REAR LAMP GUARD Code: DA2796 Round ABS plastic Tail Light & Indicator Single Defender - all models Protect those valuable lights from accidental damage either on or off-road! Will not rust and you don’t need to drill your car to fit these - fitted in seconds. They fit the tail light and indicator. -
-
BUSH KIT Code: DA1248G Rear bush kit OEM Defender - up to 9A768936 Discovery 1 Range Rover Classic from 1986 onwards Rear bush kits include bushes for top & bottom links.